Manufacturer of Linear Modules,Linear Motors,Electric Cylinders,Truss System!

About Us

Linear Module Design Service | R&D at TechMan Robotics

Want to know our capability of Linear Module Design or designing multi axis linear modules?

Author: DeMing, Engineering Director, TechMan Robotics | Published: 5th September 2016 | Category: Company Capability

Linear module design service engineering team at TechMan RoboticsMost enquiries we receive are not model numbers. They are constraints. Sometimes a stroke that no catalogue length covers, sometimes 120 mm of clearance behind a mounting face. Often a servo the customer has already standardised on, or a payload split across two carriages that must move together.

Our linear module design service exists for exactly those cases. We work backwards from the constraint to a mechanical answer, then build it. Development, machining, assembly and after-sales all sit inside one company. So the design that leaves the drawing board is one we can actually cut, align and ship.

When a Standard Module Stops Being Enough

A standard series covers a wide middle. It stops working at the edges, and the edge is usually a single parameter rather than the whole application.

Common triggers we see:

  • Stroke beyond the standard length, where critical speed rather than thrust becomes the limit
  • Installation space that fixes the module height or the closed gap between carriages
  • A motor the customer has already specified, which the module must adapt to instead of the other way round
  • Payload applied off-centre, so moment load rather than mass decides the rail size
  • Two or more axes that must hold orthogonality across a large frame
  • Environment — water, oil, chips, or a cleanroom — that rules out the open construction

Each of these leads somewhere different. Off-centre load is a rail and carriage problem. A fixed motor is an interface problem. Long travel is a rotational dynamics problem. So the first job in any non standard linear actuator project is deciding which one is binding. Every linear module design here starts from that decision.

What Our Linear Module Design Service Covers

We develop and manufacture across the full range of drive structures. Engineers can therefore compare them before committing:

That breadth matters more than it sounds. A supplier who builds only belt modules will propose a belt module. We would rather tell you that your accuracy target rules the belt out. A linear module design that starts from whatever we happen to stock is not really a design.

The embedded rail construction deserves a note of its own. In an embedded design the linear guide sits inside the module body. In the conventional arrangement the rail mounts onto the profile. The two give different housing sections, different stiffness behaviour and different sealing options. So the choice belongs at concept stage, not after the layout is fixed. Fully enclosed versions cover the screw, belt, rack and linear motor structures, in aluminium and in steel embedded bodies. We develop them against three environmental cases: water and oil ingress, water with oil plus chips or swarf, and dust-sensitive or cleanroom conditions.

Every Linear Module Design Starts With Calculation

Linear module design should not begin with a shape. Before anyone models an assembly, we check the parameters that decide feasibility. More usefully, we find which one runs out first.

For a screw driven axis we check critical speed, unsupported screw length, DN value and buckling under axial thrust. Motor-to-load inertia ratio, guide rail load and moment load follow, and all of it runs against the required stroke, speed and acceleration profile.

Two of those pull in opposite directions, which is the part that catches people out. Critical speed rises with screw diameter, so a longer axis wants a fatter screw. DN value falls as diameter grows, so a faster axis wants a thinner one. Where those two curves cross sets the practical maximum for that travel length. End fixity shifts the critical speed curve upward, because a fixed–supported arrangement buys speed through bending restraint. It does nothing for thrust duty, so it solves one problem only.

Belt driven systems move the question elsewhere. Span stiffness varies with carriage position and reaches its minimum near mid-stroke. The worst case for a belt axis therefore sits in the middle, not at either end. Tooth engagement, cord material, transmission load and servo tuning then follow from there.

The reason for doing this before geometry is blunt. If the operating parameters do not close mathematically, changing the CAD model will not solve the application. Our screw linear module selection guide works through the same decision chain in more depth for one drive type.

A Worked Example: Two Carriages, One Motor

A customer came to us with a handling application in which two carriages had to move symmetrically toward and away from each other. One 750 W servo drove both, and the customer had already standardised on that motor. Combined payload was around 110 kg, stroke 550 mm per carriage.

The mechanical answer was one opposed right-hand and left-hand rolled ball screw, ⌀20 with a 10 mm lead, accuracy class C7, in a fixed–supported bearing arrangement. Because both nuts sit on that same screw, the two carriages move in step without a second drive, a gearbox or electronic coupling. Under symmetric load their axial reactions cancel at the fixed bearing. That is why the arrangement works rather than merely fits.

Two findings from that project are worth stating. A catalogue will not tell you either of them:

The closed gap is a hardware floor, not a design choice. Our customer wanted the carriages to close as far as possible, and the minimum turned out to be 120 mm. Nut housing widths set it, plus the run-out where the right-hand and left-hand threads meet. No amount of layout work reduces it. Knowing that number early changed the customer’s gripper design instead of ours.

Critical speed bound the design, not DN value. At roughly 1,450 mm between bearing supports, the fixed–supported critical speed works out near 1,255 rpm. DN sat around 25,000, comfortably inside limits. So the motor’s 3,000 rpm capability was irrelevant, and travel speed capped out at about 10 m/min. Telling the customer that before machining beat discovering it during commissioning.

Repeat positioning accuracy on the delivered unit is ±0.01 mm. The full project, from first enquiry through to crating and shipment, is covered in a separate case study . The customer’s own motor dimension drawing drove the adapter plate design. We confirmed the project on 3D and 2D PDF drawings before cutting any material.

Long-Stroke Structures and What They Hold

Extended travel is where calculating first pays for itself, because the limiting parameter migrates as the axis grows. A screw that behaves well at 600 mm may hit its critical speed limit at 2,000 mm. Long travel therefore pushes many designs toward rack, belt or linear motor structures instead.

Long-stroke structure Repeat positioning accuracy
Linear motor driven ±0.002 mm
Screw driven ±0.01 mm
Rack and pinion driven ±0.02 mm
Belt driven ±0.04 mm

The order follows from the mechanics rather than from build quality. A linear motor removes the mechanical transmission from the position loop, so it sits at the top. That figure depends on the linear encoder specified with it. We confirm the feedback configuration per project, rather than treating it as a property of the motor. With a screw, rotation passes through a preloaded nut. That keeps a stiff, well-defined link between motor angle and carriage position. Rack drive introduces gear mesh. The belt adds an elastic tension member whose stiffness changes with carriage position along the span.

None of this ranks the structures by quality. Each figure describes what that drive can hold over long travel. That is what a machine designer needs before choosing.

How a Non Standard Linear Actuator Project Runs

Two workflows sit behind the design service, and they answer different questions.

Customer solution design answers one application. It starts from an existing mechanical platform where possible. Engineers then modify stroke, mounting, drive type, motor interface or axis layout around the machine it must fit. Its decisive checkpoint is drawing confirmation. You receive the 3D model and 2D PDF drawings. You then review geometry, mounting positions and interfaces before anything reaches machining. That step fixes the agreed stroke, dimensions and layout, and it is where late changes still cost the least.

New product development creates or revises a platform we will build repeatedly. It has to suit many customers, many strokes and many duty cycles. So it carries prototype validation, production trials and a formal design release.

Most enquiries arrive through the first route. Some of them repeat often enough to become inputs to the second. The dual-carriage arrangement above started as one customer’s problem.

From Your Layout to a Revised Proposal

A concept layout from your side is a good starting point. It is not a specification we copy.

We regularly receive an original customer arrangement and return a revised mechanical proposal. That can mean different axis stacking, a different support structure, a relocated motor or changed interface geometry. We propose it where the original layout would create an assembly, stiffness or serviceability problem later. At system level this extends to floor rail arrangements, gantry frames and granite base platforms. There the supporting structure shapes achievable accuracy as much as the modules bolted onto it.

Prototype Validation and Testing

When a design goes beyond an existing platform, it passes through validation before release. The point is not to confirm that the module moves.

Three tests carry most of the weight in our linear module design work:

Metal fatigue. A linear module accelerates, decelerates and reverses for its whole service life, and alternating loads pass through the housing, screw, guide and fastener interfaces. Fatigue testing turns that into a design input. Findings here change section thickness, rib geometry, fastener specification or assembly torque, well before routine production.

Flatness and planar consistency. A module is only as straight as the surface it references. We check flatness and planar consistency on the machined surfaces that carry the rails. A housing can pass on dimensions and still deliver a carriage that wanders in travel.

Accuracy. We verify positioning and repeat positioning behaviour on the assembled axis. The test runs under the load and duty cycle we calculated for, not unloaded on a bench.

Validation also looks at mechanical interference, transmission behaviour, guide loading and assembly feasibility. Those ordinary questions decide whether a design is finished or merely functional.

Metal fatigue and flatness testing during linear module development

Designing for the Shop Floor

A prototype that works once is not a finished design. Good linear module design also has to survive machining and assembly at volume.

So before a design enters regular production, our engineers ask a short and unglamorous list of questions. Can the required surfaces be machined consistently? Can technicians assemble the parts without heavy hand correction? Is the alignment requirement repeatable? Can the structure be serviced later? If a prototype only reaches its tolerance through hand adjustment, the design needs revision rather than a more patient technician.

Keeping machining in house gives that judgement something to stand on. We machine ball screws and guide rails ourselves, alongside parts machining, secondary operations and assembly. Our production sequence also begins with engineering selection, ahead of material purchasing. Feedback then travels back the other way. Machining may show that an interface can be simpler, or assembly may find a clearance issue. Functional testing may show that a sensor position or cable route should change. All of it returns to the engineers who drew it.

In-house ball screw and guide rail machining

Multi-Axis Linear Module Design

Development does not end at a single axis. Many applications combine two or more axes into XY and XYZ systems, gantry structures, Cartesian robots, vertical lifting axes or long-travel positioning platforms.

At that point the problem changes shape. The team is no longer selecting a module. It coordinates axis stacking order, structural support, payload distribution, overhung moment, orthogonality, cable routing and assembly sequence. This is also why single-axis accuracy figures do not add up to multi-axis performance. Error stacks across three orthogonal axes, and the frame contributes as much as the modules.

9. Custom multi-axis gantry system with granite base platform

Custom multi-axis gantry system with granite base platform

What the Linear Module Design Service Hands Over

Design release means more than a drawing. Engineering issues the document set that the factory then works to: 2D manufacturing and assembly drawings, the bill of materials, and work instructions for machining and assembly. Dimensional inspection charts, guide rail and ball screw inspection sheets, profile inspection criteria and tolerance management standards come from the same source.

That last group is the part worth pausing on. The engineers who set the requirement also write the criteria the product will be measured against. When a design changes, a controlled drawing revision carries the inspection documents with it. Development defines the target; production then has to reproduce it.

After Delivery, Feedback Returns to Engineering

Our after-sales support engineers sit in the same department as product development. So a recurring installation difficulty reaches the person who owns the drawing, not a service desk. That is what makes the development cycle a loop:

Constraint → Calculation → Structure selection → 3D and 2D design → Drawing confirmation → Prototype or production trial → Validation → Design release → Field feedback

FAQ

Can you design around a motor we already use?

Yes, and it is one of the more common requests. Send the motor dimension drawing and shaft specification. We design the adapter plate, coupling and bearing arrangement around it. The dual-carriage project above worked exactly that way.

How long does a custom project take?

A non standard linear module design usually comes back as 3D drawings within about three days of receiving your constraints. Once you confirm those drawings, production runs 10 to 12 days through to shipment. A design that needs prototype validation, rather than a modification to an existing platform, takes longer than that.

We only have a layout sketch, not a specification. Is that enough to begin?

Usually. A sketch plus the constraints is usually enough: stroke, payload, orientation, available envelope, accuracy target and duty cycle. Our engineers can then identify the binding parameter and come back with a proposal. A model number alone tells us much less.

How do we confirm the design before you start machining?

You receive a 3D model and 2D PDF drawings covering overall dimensions, effective stroke and mounting hole positions. Motor and gearbox interfaces, carriage dimensions, cable routing and sensor positions appear on them too, and machining starts only after you confirm them.

Does every custom project need a prototype?

No. Projects that modify an existing platform usually go straight to production after drawing confirmation. That covers changes to stroke, mounting, motor interface or sealing. Prototype validation applies when the structure itself is new.

What certification does the product carry?

Modules are built under an ISO 9001 quality management system and carry CE marking, including Machinery Directive conformity.

Start a Linear Module Design Project

If a standard module does not fit your machine, the constraints are more useful to us than a model number.

Send your layout or drawing, along with stroke, payload, speed, accuracy target and installation orientation. Add the available envelope, duty cycle, environment and any motor you have already specified. Our engineers will tell you which parameter actually limits the application. They will also say whether a standard configuration holds it, or whether the job calls for a custom linear module design. On non standard work you can expect 3D drawings back within roughly three days. Want to check our manufacturing?

 

Prev:

Next: