Manufacturer of Linear Modules,Linear Motors,Electric Cylinders,Truss System!

Linear Motor Systems/Linear Motion/

  • Product Details

TMTL series are our range of Linear Motor with Embedded Guide Rail

Author: DeMing, Engineering Director | Published: 7th,Sept 2016 | Category: Linear Motor Systems

TMTL is a linear motor with embedded guide rail: the rail, the forcer, the magnet track and the position scale all sit inside one extruded aluminium body rather than being bolted onto a frame. This page gives the complete parameter set for all thirteen models, both dimensional tables, the model code, and the arithmetic that decides what any given model will actually do on your machine.

At a glance

  • Rated thrust 38–561 N, peak thrust to 2,244 N
  • Repeat positioning accuracy ±0.005 mm (magnetic scale) or ±0.003 mm (optical scale)
  • Body width 60 / 82 / 95 / 115 / 145 / 165 / 195 mm
  • Stroke 40 mm to 3,780 mm, ordered in 60 mm steps
  • Max speed 1.5–2 m/s (CM) · 1–1.2 m/s (CR)
  • Feedback: incremental or absolute, magnetic or optical
  • Control: pulse, EtherCAT or analogue

[Request a quotation]   [Download the TMTL datasheet]

Why the Embedded Guide Rail Changes the Load Path

TMTL forcer is magnetically pulled toward the magnet track underneath it at all times, energised or not. That attraction is a permanent normal load sitting on the guide rail, in addition to whatever the machine is carrying.

(For the motor-technology background behind that attraction, see the dedicated ironcore linear motor page).

The question that follows is where that load goes. On a built-up axis it passes from the rail into a bolted joint and only then into the machine base, and the joint decides the stiffness. A linear motor with embedded guide rail removes the joint: the rail seat and the body are one extrusion, so the rail, the forcer, the magnet track and the scale all reference the same piece of metal, and the attraction closes through the structure.

Two consequences follow that matter at selection time.

The first is that an embedded guide rail makes this a complete axis, not a motor kit. The rail is already sized for the attraction plus the rated payload, and the air gap between forcer and track is set at assembly. You cannot separate the parts and re-mount them on your own rail without redoing both.

The second is that the payload figures in the table below are structural limits, not motor limits. They are set by the rail, the carriage length and the body section — which is why they do not track rated thrust in a straight line. Read the payload column directly rather than inferring capacity from the thrust rating or the body width.

Structure of the TMTL linear motor with embedded guide rail — rail, forcer, magnet track and linear scale all reference a single aluminium body

TMTL-PM: Complete Model Data

Payload figures apply at 0.5 m/s and 0.5 G. Repeat positioning accuracy is ±0.005 mm with a magnetic scale and ±0.003 mm with an optical scale on every model.

Model Width (mm) Rated thrust (N) Peak thrust (N) Cont. current (A) Peak current (A) Thrust const. (N/A) Payload horizontal (kg) Payload side-mounted (kg) Max speed CM/CR (m/s) Max accel. CM/CR (G)

Stroke (mm)

TMTL60-PM38

60

38 152 2.5 10 15.2 10 8 1.5 / 1 1.5 / 1

40–1360

TMTL82-PM52

82

52 208 2.5 10 20.8 15 10 2 / — 2 / — 60–1800
TMTL82-PM98

82

98 392 2.5 10 39.2 20 15 2 / 1.2 2 / 1

80–1760

TMTL100-PM110

95

110 442 2.5 10 44.0 23 18 2 / — 2 / —

60–3780

TMTL100-PM147

95

147 588 2.5 10 58.8 25 20 2 / — 2 / —

60–3720

TMTL120-PM152

115

152 609 2.5 10 60.8 35 25 2 / — 2 / —

60–3780

TMTL120-PM203

115

203 812 2.5 10 81.2 45 28 2 / — 2 / —

60–3720

TMTL145-PM225

145

225 900 5 20 45.0 60 38 2 / — 2 / —

60–3720

TMTL145-PM337

145

337 1350 5 20 67.4 75 50 2 / — 2 / —

60–3660

TMTL165-PM299

165

299 1196 5 20 59.8 70 45 2 / — 2 / — 60–3720
TMTL165-PM447

165

447 1790 5 20 89.4 85 60 2 / — 2 / —

60–3660

TMTL195-PM392

195

392 1568 5 20 78.4 80 55 2 / — 2 / —

60–3720

TMTL195-PM561 195 561 2244 5 20 112.2 95 70 2 / — 2 / —

60–3660

Thrust constant is rated thrust divided by continuous current — the figure to hand your drive supplier. A dash in the CM/CR columns means the fully-closed CR construction is not offered for that model.

What the Numbers Mean in Practice

Peak thrust is a duty allowance, not a rating

Peak thrust is exactly four times rated thrust on all thirteen models, because peak current is exactly four times continuous current and thrust in a linear motor tracks current. Nothing mechanical changes at the peak figure.

What does change is heat. Resistive loss goes with the square of current, so drawing peak current puts sixteen times the continuous heat into the coils. The peak column covers the acceleration segment of a move and nothing longer. If your profile spends a meaningful share of each cycle above rated thrust, the model is undersized regardless of what the peak number says.

The 2.5 A and 5 A frames are two different families

Thrust constant climbs steadily across the 2.5 A frames — 15.2 N/A on the TMTL60 up to 81.2 N/A on the TMTL120-PM203 — then restarts lower at 45.0 N/A on TMTL145-PM225, which is the first 5 A frame. A larger frame does not automatically mean more force per amp. Check the constant against the drive you intend to use rather than assuming it rises with size.

Short strokes never reach the catalogue speed

Reaching 2 m/s at 2 G takes about 102 mm of travel, and stopping takes the same again, so roughly 204 mm disappears into ramping before any constant-velocity segment exists. At 1.5 m/s and 1.5 G the figure is about 153 mm; on the TMTL82-PM98-CR at 1.2 m/s and 1 G it is about 147 mm.

The practical effect is easiest to see on the TMTL60, whose stroke starts at 40 mm. Its four shortest stroke steps — 40, 100, 160 and 220 mm — are all shorter than or barely equal to its own ramping distance. Those axes run triangular profiles, and the number that governs cycle time is acceleration, not top speed.

Side-mounted capacity is a separate column

Every model carries less side-mounted than horizontal, because the load acts as a moment on the carriage instead of straight down through it. The gap widens with frame size: eight against ten kilograms on the TMTL60, seventy against ninety-five on the TMTL195-PM561. Take the figure from the column that matches your mounting, and confirm any orientation other than these two.

Heat leaves through the machine base

The forcer coils dissipate into the aluminium body, so the mounting surface is part of the thermal path. On a continuously cycling axis the body warms, and aluminium moves roughly 23 µm per metre per degree — well above the repeatability figure. Repeatability describes a settled axis returning to the same point; it does not describe absolute accuracy along a warmed-up long stroke. On axes where that distinction matters, plan the scale mounting and the heat path deliberately.

Stroke Comes in 60 mm Steps

Stroke is not continuously variable. It is built as S = 40 + N1, 60 + N1 or 80 + N1 depending on the model, where N1 is any multiple of 60.

Base Models Available strokes
40 + N1 TMTL60-PM38 40, 100, 160 … 1360
60 + N1 TMTL82-PM52, all TMTL100 / 120 / 145 / 165 / 195 60, 120, 180 … up to the model maximum
80 + N1 TMTL82-PM98 80, 140, 200 … 1760

A 500 mm requirement on a 60 + N1 model therefore becomes 480 mm or 540 mm. Settle this before the machine layout is fixed, not after.

Installed length is L = S + L1. Worked example: a TMTL100-PM147 at 1,740 mm stroke has L1 = 280, giving L = 2,020 mm. That exceeds the 1,200 mm profile-cover threshold for the TMTL100 frame, so it ships with a steel-strip cover and the total length reduces by 4 mm to 2,016 mm. Reserve the P0 + P1 overtravel allowance at each end on top of the effective stroke.

Model Code

Example: TMTL82C2-PM98-S1000-C05-PS-4.5A-N03-CM-BL

Segment

Meaning

In the example

TM TechMan TM
TL Embedded linear motor structure TL
60 / 82 / 100 / 120 / 145 / 165 / 195 Size code 82
C2 Number of carriages — omitted for a single carriage 2 carriages
PM98 Motor series and rated thrust 98 N
S1000 Stroke 1000 mm
C / G / CJ / GJ Scale type Magnetic
05 / 10 Resolution: 05 = 0.5 µm, 10 = 1 µm 0.5 µm
GG / XSD / GC / PS / CU Drive brand: Googol, Step, Servotronix, Panasonic, customer-specified Panasonic
4.5A Rated current 4.5 A
N / E / A Control method Pulse
N / 03 / 05 / 08 / 10 Cable length in metres, N for no cable 3 m
CM / CR Semi-closed or fully-closed Semi-closed
BL / blank Black or silver finish Black

The size code and the body width differ on two sizes: code 100 is a 95 mm body and code 120 is a 115 mm body. The other five codes match their widths.

Configuration Options

Scale type

Code Scale Resolution Repeat positioning accuracy Homing at power-up
C Incremental magnetic 1 µm ±0.005 mm Required
G Incremental optical 0.5 µm ±0.003 mm Required
CJ Absolute magnetic 1 µm ±0.005 mm Not required
GJ Absolute optical 0.5 µm ±0.003 mm Not required

Specify an absolute scale wherever a homing move after a power interruption would be awkward — an axis parked with tooling inside a fixture, a vertical axis, or a gantry whose two carriages must not home independently. It also lets you delete the origin sensor.

  • Control interface — pulse (N), EtherCAT (E) or analogue (A).
  • Origin sensor — NPN, PNP, or none.
  • Cable — 3 m, 5 m, 8 m, 10 m, or supplied without cable.
  • Environment — CM semi-closed for general factory conditions, CR fully-closed for dust-free rooms. CR is offered on TMTL60-PM38 and TMTL82-PM98 only, and it carries lower speed and acceleration ceilings because the full-length seal adds drag along the travel. The CR body is also dimensionally different from its CM equivalent — it is not a CM module with a cover added.
  • Lubrication — external oil nozzles on both sides of the body, so the rail can be greased without lifting the cover or dismantling the carriage.

Dimensions

All figures in mm. D through D5 are nested hole pitches on the carriage top plate measured along the direction of travel, D being the outermost; a zero means that pattern is not present on that model. W2, W3 and W4 are the corresponding transverse dimensions. Module mounting holes sit at a fixed 120 mm pitch; T1 is the end margin from the module face to the first hole, and closes out the length as T1 = (L − 120 × (N − 1)) / 2, where N is the number of mounting holes. Because L varies with stroke, so does T1 — take it from the confirmed drawing.

TMTL(60–195)-PM-CM

Model

W W1 H S L1 P0 P1 D D1 D2 D3 D4 D5 W2 W3/W4 M B

E

TMTL60-PM38-CM 60 58 65 40+N1 164 22 10.5 99 0 0 0 66 30 51 50 M4 × 8 deep Ø3H7 × 5 deep M4 c-bore
TMTL82-PM52-CM 82 80 76 60+N1 214 29 8 140 0 0 115 66 30 71 68 M4 × 8 deep Ø4H7 × 5 deep M5 c-bore
TMTL82-PM98-CM 82 80 76 80+N1 254 29 8 180 0 0 150 75 30 71 68 M4 × 8 deep Ø4H7 × 5 deep M5 c-bore
TMTL95-PM110-CM 95 129 78 60+N1 220 35 10 130 0 0 0 102 50 115 76 M5 × 12 deep Ø5H7 × 6 deep M5 c-bore
TMTL95-PM147-CM 95 129 78 60+N1 280 35 10 190 0 0 160 102 50 115 76 M5 × 12 deep Ø5H7 × 6 deep M5 c-bore
TMTL120-PM152-CM 115 151 78 60+N1 220 35 10 130 0 0 0 102 50 137 95 M5 × 12 deep Ø5H7 × 6 deep M6 c-bore
TMTL120-PM203-CM 115 151 78 60+N1 280 35 10 190 0 0 160 102 50 137 95 M6 × 12 deep Ø5H7 × 6 deep M6 c-bore
TMTL145-PM225-CM 145 180 95 60+N1 280 35 10 190 0 0 160 102 50 165 122 M6 × 12 deep Ø5H7 × 6 deep M6 c-bore
TMTL145-PM337-CM 145 180 95 60+N1 340 35 10 250 0 220 160 102 50 165 122 M6 × 12 deep Ø6H7 × 6 deep M6 c-bore
TMTL165-PM299-CM 165 200 98 60+N1 280 35 10 190 0 0 160 102 50 185 142/102 M6 × 12 deep Ø6H7 × 6 deep M6 c-bore
TMTL165-PM447-CM 165 200 98 60+N1 340 35 10 250 220 160 140 102 50 185 142/102 M6 × 12 deep Ø6H7 × 6 deep M6 c-bore
TMTL195-PM392-CM 195 230 102 60+N1 280 35 10 190 0 0 160 102 50 215 168/128 M6 × 12 deep Ø6H7 × 8 deep M6 c-bore
TMTL195-PM561-CM 195 230 102 60+N1 340 35 10 250 0 220 160 102 50 215 168/128 M6 × 12 deep Ø6H7 × 8 deep M6 c-bore

TMTL(60–82)-PM-CR

Model

W

W1 H S L1 P0 P1 D D1 D2 D3 W2 W3 M

B

TMTL60-PM38-CR 60 58 65 40+N1 164 15.5 4 125 0 0 70 51 50 M4 × 8 deep Ø3H7 × 4 deep
TMTL82-PM98-CR 82 83.5 72 80+N1 254 19 8 200 150 75 30 71 68 M4 × 8 deep Ø4H7 × 5 deep

Comparing the two tables shows why a CR module needs its own drawing.TMTL82-PM98 carriage pattern changes completely between constructions — D1, D2 and D3 read 0, 0 and 150 on the CM version and 150, 75 and 30 on the CR — and both P0 and P1 shrink. A fixture drilled from the CM drawing will not bolt to the CR carriage.

Cover construction. TMTL100 and TMTL120 modules use a profile cover below 1,200 mm total length and a steel-strip cover above it; TMTL145, TMTL165 and TMTL195 switch at 1,700 mm. The steel-strip version reduces total length by 4 mm.

Replacing a Screw or Belt Module in an Existing Frame

A linear motor with embedded guide rail is dimensioned to go where a screw or belt module of similar width currently sits. Three things change when it does, and all three are layout questions rather than performance questions.

The end allowance changes shape. A screw module reserves length for the bearing housings and the motor, which usually sits beyond one end or on a folded-back mount. A TMTL reserves P0 + P1 at each end and nothing beyond, so the axis footprint becomes symmetrical and the motor bulge disappears — but the cable exit becomes a permanent feature of the moving carriage rather than a fixed point at one end. Plan the energy chain before, not after.

The holding behaviour changes. A screw holds its position mechanically when power is removed. A direct-drive axis does not: it holds by drawing current, and it drifts when disabled. Any application that relies on the axis staying put through a power cycle needs a brake specified into the design from the start.

The stroke becomes quantised. A screw module is cut to whatever length you ask for. A TMTL stroke lands on the 60 mm grid described above, so a retrofit into fixed hard stops usually means choosing the next step down and re-setting the stops.

For the wider question of which drive type suits an application in the first place, see the screw linear module selection guide  and belt linear module accuracy

Where the TMTL Series Fits

Grouped by motion duty rather than by industry, because duty is what the selection turns on.

Short-stroke, high-cycle indexing. Tens of millimetres, thousands of times an hour, with a settling requirement at each end. Nothing in the drive path accumulates wear at one narrow band of travel, which is the failure mode a screw nut or belt tooth eventually shows on this duty.

Constant-velocity scanning. Passes where velocity ripple appears in the result. Drive tuning and scale resolution govern the outcome here, not peak thrust.

Long-travel transfer. Strokes past two metres on TMTL100 frame and larger, reaching 3,780 mm, where a screw would be working against critical speed.

Continuous reciprocation. Packaging and print axes that never really stop, where the recurring maintenance task is rail lubrication through the external nozzles.

Dust-free stations.  CR construction, on the two sizes that offer it. Confirm the particle class requirement against the seal specification before ordering.

FAQ about Linear Motor with Embedded Guide Rail

What is a linear motor with embedded guide rail?

It is a direct-drive axis in which the profiled guide rail is carried inside the motor’s own aluminium body instead of being mounted onto a separate frame. The rail seat, the forcer, the magnet track and the position scale therefore share one machined datum. The practical difference is that the module arrives dimensioned, aligned and validated as a single axis, and that the forcer’s magnetic attraction is already accounted for in the rail rating.

Why does stroke come in 60 mm steps rather than any length I ask for?

The body extrusion, the magnet track and the mounting-hole pattern are all built on the same 60 mm module. Stroke is therefore ordered as 40, 60 or 80 mm plus a multiple of 60 depending on the model. Anything between steps means a non-standard build, which is possible but goes through engineering review rather than the standard order path.

Why is peak thrust exactly four times rated thrust on every model?

Because peak current is four times continuous current, and thrust is proportional to current. It is a current limit, not a mechanical one, and it is bounded by heating rather than by strength.

Does a wider body always carry more?

No. Payload is set by the rail, the carriage length and the body section together, and the table does not rise in a straight line with either thrust or width — TMTL100-PM147 is listed above TMTL120-PM152 on both payload columns despite the narrower body. Read the payload column for the specific model and mounting orientation rather than reasoning from frame size.

Why is the fully-closed CR construction only available on two models?

The seal runs the full length of travel and its drag scales with stroke and frame size. On the two sizes offered, the ceilings drop accordingly: TMTL60-PM38 goes from 1.5 to 1 m/s and TMTL82-PM98 from 2 to 1.2 m/s. On larger frames the trade stops being worthwhile, so those sizes are semi-closed only.

My stroke is 150 mm. Will the axis reach 2 m/s?

No. Ramping to 2 m/s at 2 G and back consumes roughly 204 mm, more than the whole travel. Size that axis on acceleration and settling time and treat the catalogue speed as inapplicable to it.

Can I buy the motor and fit it to my own rail?

Not from this series. In a linear motor with embedded guide rail the rail is sized for the forcer attraction as well as the payload, and the air gap between forcer and magnet track is set during assembly against the body datum. The TMTL ships and is validated as a complete axis. If you need a separate forcer and track, that is a different product family — ask and we will point you at it.

What changes if I specify an absolute scale instead of an incremental one?

The homing move disappears. After a power interruption the drive already knows where the carriage is, so the axis can be re-enabled in place. That matters on vertical axes, on axes parked inside a fixture, and on gantries where two carriages must not home against each other. It also allows the origin sensor to be omitted.

How is positioning performance verified before shipment?

Positioning accuracy and repeatability are measured with a laser interferometer against a granite datum, and linear motor speed testing is part of the standard pre-shipment sequence. Inspection footage is published on the TechMan Robotics YouTube channel; the full sequence is described under linear module quality control. 

Request a TMTL Sizing Review

Body width is the last thing to choose. Send the motion profile and we will size the axis against it:

  • Effective stroke, and which mounting orientation
  • Moving mass — workpiece, fixture, tooling, sensors, mounting plate, cable carrier
  • The move itself: distance, target move time, dwell time, moves per hour
  • Required settling time and positioning tolerance
  • Any process force acting along or across the axis
  • Environment: general factory, dust-free, or something we should ask about
  • Controller or PLC brand, and EtherCAT or pulse
  • Cable length and preferred exit direction

You get back a recommended model, scale type and drive configuration, with the stroke rounded to the nearest available step and the installed length calculated. For non-standard work, 3D drawings return in about three days, and production runs 10–12 days from drawing confirmation to shipment.

Multi-carriage, gantry and other non-standard configurations are handled as engineering projects –see linear module designor visit ourvideo gallery.

 

Prev:

Next:

Inquiry

    PersonalBusinessDistributor