Manufacturer of Linear Modules,Linear Motors,Electric Cylinders,Truss System!

Truss & Robot Track Systems/Linear Motion/

  • Product Details

Lathe Gantry Loader Configuration: Layout codes, axis travel, cycle time and the 90° loading gripper

Author: DeMing, Engineering Director | Published: 11th, Sept 2026 | Category: Truss & Robot Track Systems

Two dimensions settle most of a lathe gantry loader configuration. One is how far the X axis travels between the chucks and the part station. The other is how far the Z axis has to drop to reach the spindle. Speed and the gripper are then chosen around those two lengths.

This guide decodes the four loader layouts in the truss catalogue and works through what the published 7-second cycle means in practice. It closes with the data the 90° loading gripper needs. Layouts and applications from the buyer’s side are on the TallMan Robotics CNC lathe gantry loader page.

Lathe Gantry Loader Configuration by layout

A lathe gantry loader configuration is written in the same TM-TS code as the truss manipulators, read field by field in the truss manipulator selection guide.

Layout Example code Column X axis Y axis Z axis End load
Lathe Gantry Loader Configuration: CNC_lathe_gantry_loader_serving_a_single_lathe_with_a_part_station_beside_itStandard single-machine TM-TS-CM-H2.5M-X3M20+Z2M15-15KG 2.5 m 3 m, 2.0 m/s — 2 m, 1.5 m/s 15 kg

Lathe Gantry Loader Configuration: one_to_two_CNC_lathe_gantry_loader_serving_two_lathes_from_a_shared_part_stationOne-to-two

TM-TS-CM-H2.2M-X7M20+Z2M15-15KG 2.2 m 7 m, 2.0 m/s — 2 m, 1.5 m/s 15 kg
Lathe Gantry Loader Configuration: custom_CNC_lathe_gantry_loader_system_for_a_line_of_lathesCustom lathe line TM-TS-CM-H2.8M-2(X20M15+Z2M10)-30KG 2.8 m 2 sets, each 20 m, 1.5 m/s — 2 m, 1.0 m/s per set 30 kg

Lathe Gantry Loader Configuration: Ram_type_three_axis_lathe_gantry_loader_with_H_section_column

Ram-type three-axis

TM-TS-CM-H2M-X10M15+Y0.5M10+Z4M15-50KG 2 m 10 m, 1.5 m/s 0.5 m, 1.0 m/s 4 m, 1.5 m/s 50 kg

In the line code, the bracket groups an X axis and a Z axis into one set. The 2 in front of it means two identical sets. That matches the two parallel beams in the example layout.

Layout Load Length Cantilever Repeatability Speed
CNC_lathe_gantry_loader_serving_a_single_lathe_with_a_part_station_beside_itStandard single-machine 0–100 kg 0–3 m 0–1 m ±0.05 mm 0–2 m/s
one_to_two_CNC_lathe_gantry_loader_serving_two_lathes_from_a_shared_part_stationOne-to-two 0–100 kg 0–6 m 0–1 m ±0.05 mm 0–2 m/s
custom_CNC_lathe_gantry_loader_system_for_a_line_of_lathesCustom lathe line 0–100 kg 0–100 m 0–1 m ±0.05 mm 0–2 m/s
am_type_three_axis_lathe_gantry_loader_with_H_section_columnRam-type three-axis 0–100 kg 0–100 m 0–1 m ±0.05 mm 0–1.5 m/s

X travel is set by the layout

On a single-machine loader the X axis only has to span the chuck and the part station beside it. That is why the published length stops at 3 m. The one-to-two loader puts its part station between two lathes and has to reach both chucks, so its range runs to 6 m. A line loader is sized to the plant and published to 100 m.

In any lathe gantry loader configuration, travel length feeds straight into cycle time. At 2 m/s the X axis covers 3 m in 1.5 s of constant-speed running. A 6 m traverse at the same speed takes 3 s, before acceleration, deceleration and settling are added at each end.

Z stroke, column height and the ram-type loader

The X–Z loaders reach the chuck with a 2 m Z axis hanging from a beam on columns 2.2 to 2.8 m high. The ram-type loader works differently. Its Z axis is 4 m long and runs at 1.5 m/s. A 0.5 m Y ram on the X carriage moves that Z axis across the machine.

A long vertical axis moving fast is a stiffness problem. Treat the extended Z axis as a cantilever loaded at its tip, and deflection grows with the cube of its free length (δ = FL³/3EI). Doubling the free length therefore multiplies tip deflection by eight under the same lateral force. The catalogue’s answer is structural. The main column of the ram-type loader is an H-shaped section, which raises column stiffness and holds the Y and Z axes stable at speed. The Y ram itself stays short at 0.5 m.

A practical consequence follows for layout. An X–Z loader works in a single vertical plane under its beam, so every chuck and part station has to sit on that line. When the part station cannot sit under the beam, the Y ram supplies the cross movement.

What the 7-second cycle covers in Lathe Gantry Loader Configuration

The catalogue rates the standard single-machine loader and the one-to-two loader as capable of a 7-second cycle. It does not break the figure down. Build it up for the real cell before a cycle time goes into a line specification.

The gripper fixes one part of the cycle, since it exchanges a part in 0.3 to 0.6 s. The rest is axis travel. The Z axis goes down and up at the chuck and again at the part station, and the X axis traverses between them in each direction. On a one-to-two cell the traverse to the far lathe is longer than to the near one. The cycle therefore depends on which machine is being served. Take the chuck-to-station distances from the layout drawing and check the cycle against them.

The 90° loading gripper

90 degree pneumatic loading gripper with two three-jaw heads for lathe gantry loader

Pneumatic loading gripper with two heads set at 90°.

The lathe loading gripper is pneumatic, with two gripping heads set 90° apart on one body. The finished part and the blank are exchanged in a single visit to the chuck. The catalogue credits the 90° layout with higher repeat positioning accuracy in the exchange and a longer service life.

Gripper specification Value
Load 0–3 kg
Repeat positioning accuracy ±0.05 mm
Exchange time 0.3–0.6 s per cycle
Actuation Pneumatic

As the jaws close, the gripper guides the workpiece into alignment, and a spring-loaded pusher feeds it home. A compressed-air blow-off clears chips before the new part goes in. Its compact body keeps the switching movement short.

Being pneumatic, it needs a clean, regulated compressed-air supply at the loader. The 3 kg limit applies per part. Heavier parts need a different gripping method, chosen from the options on the selection sheet.

Data a Lathe Gantry Loader Configuration needs

Loaders are specified on the truss selection sheet, and three of its blocks carry most of the configuration.

The first is the part: its name, form, dimensions and weight, with a drawing. Weight decides whether the 3 kg pneumatic gripper applies, while form and dimensions decide the jaws.

The second is rotation. The sheet asks whether an R axis or an A axis is needed. A part that has to be turned over between a first and a second operation needs one.

The third is supply and controls. The loader can ship as bare mechanics, with electrical accessories, or with its electrical program written. The motor, reducer, sensors, touch screen and PLC can be named by brand or supplied by the customer, and sensors are specified NPN or PNP. This is also the stage at which the signal exchange between the loader and the lathe control is agreed.

FAQ about Lathe Gantry Loader Configuration

What is the heaviest part the standard loaders can handle?

The standard pneumatic gripper is limited to 3 kg per part. The loaders are published for loads up to 100 kg. On the single-machine and one-to-two units, the example codes rate the end of the arm at 15 kg. Parts over 3 kg need a different gripper.

Why is the ram-type loader slower than the X–Z loaders?

It is published at up to 1.5 m/s against 2 m/s for the X–Z units. Its Z axis is twice as long. At full extension a longer vertical axis deflects more under the same acceleration forces, which is the likely reason for the lower top speed.

Prev:

Next:

Inquiry

    PersonalBusinessDistributor